Barco CTPN-41B Manual de usuario Pagina 36
- Pagina / 68
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
36CT series User Manual - Overview
english
5.7 Installation main menu
image orientation: Rotate the image on the imaging device in desktop front, desktop rear, ceiling
front, ceiling rear.
source scan
: Search through all input connectors for an active signal or stay on one connector.
IR front
Enable or disable front IR-receiver.
IR rear Enable or disable rear IR-reciever.
OSD enable
: Sets how the OSD messages should appear.
On: All OSD messages are shown.
Only warnings: Only critical OSD messages are shown.
Off: No OSD messages are shown. The OSD menu is still accessible by clicking
menu on either the remote or the keypad.
test image:
Displays internal test images for projector alignment and setup. Option to show
4:3, 16:9, 16:10, 1.85:1, 2.35:1, 5:4, combined, off
4:3: fills the imaging device with a white image, but marks out the 4:3 area in the
center of the image.
16:9: fills the imaging device with a white image, but marks out the 16:9 area in
the center of the image.
16:10: fills the imaging device with a white image, but marks out the 16:10 area
in the center of the image.
1.85:1: fills the imaging device with a white image, but marks out the 1.85:1 area
in the center of the image.
2.35:1: fills the imaging device with a white image, but marks out the 2.35:1 area
in the center of the image.
5:4: fills the imaging device with a white image, but marks out the 5:4 area in the
center of the image.
Combined: fills the imaging device with a white image and marks out the all of
the above aspect ratios.
sync termination VGA
: Enable sync termination to 75 Ω /2.2 kΩ
sync termination SYNC1
: Enable sync termination to 75 Ω /2.2 kΩ
sync termination SYNC2
: Enable sync termination to 75 Ω /2.2 kΩ
sync termination SYNC3
: Enable sync termination to 75 Ω /2.2 kΩ
DisplayPort 1 eq Choice between
Normal, High, Low (enables receiving signals via longer cables/with higher bit rate)
DisplayPort 2 eq Choice between Normal, High, Low (enables receiving signals via longer cables/with higher bit rate)
picture by picture Show two sources side by side
picture by picture setup Choose the two sources to be shown side by side
EDID
: Sub menu for EDID, see chapter 5.7.1.
synchronization: Sub menu for synchronization see chapter 5.7.2 .
- CT series 1
- User Manual 1
- CT series User Manual 2
- Contents 3
- 5 Overview 25 4
- 6 Functionality 49 4
- 7 Optimising the image 55 5
- 9 Lamp change 65 5
- 6User Manual - Introduction 6
- 1 Introduction 7
- 8User Manual - Introduction 8
- 2 Safety and compliance 9
- 2.3 FCC compliance 10
- 2.4 Disposal information 11
- 2.5 Service 11
- 12User Manual - Introduction 12
- 3 What is in the box? 13
- 14User Manual - Introduction 14
- 4 Installation 15
- 4.2 Ventilation 16
- 4.3 Ceiling and rig mounting 17
- 4.4 Locking the projector 17
- 4.5 Projector angle (tilt) 17
- 4.6 Selecting a lens 18
- 4.6.1 Inserting a lens 19
- 4.6.3 Lens range 19
- 4.7 Lens lock 20
- 4.8 Lens shift 20
- 4.10 Zoom, focus and iris 21
- 4.11 Making the connections 22
- 4.15 Image sizes 23
- 24User Manual - Introduction 24
- 5 Overview 25
- Lamp Door Air Inlet 26
- Ceiling/Rig Mounting Features 26
- Accessory Mounting Features 26
- 5.1 Keypad and indicator 27
- 5.2 Wireless remote control 28
- 5.3 Connectors 29
- 5.4 Menu system 30
- 5.5 3D main menu 31
- 5.6 Picture main menu 33
- 5.7 Installation main menu 36
- 5.8 Settings main menu 39
- 5.9 Languages main menu 43
- 5.10 Status main menu 44
- 6 Functionality 49
- 6.3 Language 50
- 6.4 System status 50
- 6.5 Lamp power 51
- 6.10 PIN code 52
- 6.12 Software upgrades 53
- 54User Manual - Introduction 54
- 7 Optimising the image 55
- 7.1.2 RealColor™ modes 56
- Figure 7-1. CIE chart 57
- 7.3 Gamma 58
- Figure 7-4. Film 2.8 gamma 59
- Figure 7-5. Video 1 gamma 59
- Figure 7-6. Video 2 gamma 59
- 60User Manual - Introduction 60
- 62User Manual - Introduction 62
- 8 Technical specifications 63
- 64User Manual - Introduction 64
- 9 Lamp change 65
- 66User Manual - Introduction 66
- F50 User Manual - Lamp change 66
- PRODUCTION ADDRESS 68
Relacionado con productos y manuales para Proyectores de datos Barco CTPN-41B
(89 paginas)
Proyectores de datos Barco PHWX-81B Manual de usuario
(113 paginas)
(113 paginas)
Proyectores de datos Barco RLM-W12 Guía de usuario
(63 paginas)
(63 paginas)
Proyectores de datos Barco FLM R22+ Guía de usuario
(243 paginas)
(243 paginas)
Proyectores de datos Barco Galaxy NW-7 Guía de usuario
(183 paginas)
(183 paginas)
Proyectores de datos Barco F50 Manual de usuario
(66 paginas)
(66 paginas)
Proyectores de datos Barco RLM W6 Guía de usuario
(57 paginas)
(57 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.243 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales