Barco Projector Toolset Especificaciones Pagina 118
- Pagina / 245
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8. Configurator, Projector adjustment settings
8.3 Configuring an input slot
What should be done?
Some input modules can accept different sources. The projector must know which type of source is con-
nected to the input.
How to configure
1. Select the window for which the input must be configured (a1, a2). (image 8-5)
2. Click on Adjust (b).
The Input dialog box opens.
3. Click on Settings and select Input mode.(image8-6)
The Input mode dialog box opens with the current active setting filled out.
4. Click on the combo box next to Input mode and select the correct setting.
5. Click Close to return.
Image 8-5
Open the adjustment mode
114 R5976924 PROJECTOR TOOLSET 16/04/2009
- Projector Toolset 1
- Copyright © 3
- Trademarks 3
- TABLE OF CONTENTS 5
- Table of contents 10
- 1. BASIC CONCEPTS 11
- 1. Basic concepts 12
- 2. INSTALLATION 13
- 2. Installation 14
- 2.4 Starting up 16
- 2.7 About this manual 21
- 3. MENUS 23
- 3.3 Main window 24
- 3.4 Short cut keys 25
- 3.5 Workspace Explorer 25
- 3.6 How to adjust a setting 26
- 3.7 About Projector Toolset 26
- 3. Menus 27
- 3.8 Snapshot management 30
- 4. PREFERENCES 39
- 4.3 Access level 40
- 4.4 Software Appearance 41
- 4. Preferences 42
- 4.5 Bug report setup 44
- 4.6 Logging 45
- 4.7 Workspace selection 46
- 5. CONFIGURATOR 49
- 5. Configurator 50
- 5.5 Reconnect a projector 61
- 5.6 Move projector to a group 63
- 5.7 Edit projector properties 64
- 5.8 Configuration preview 66
- 5.9 Configuration properties 66
- 6. CONFIGURATOR, GENERAL 75
- PROJECTOR SETTINGS 75
- Image 6-1 76
- Start up general settings 76
- 6.2 Control interface 77
- Toggling the lamp 78
- 6.6 Test pattern short cuts 79
- 6.7 Test patterns, others 80
- 6.8 Advanced controls 81
- Options for Free run 82
- Image 6-11 83
- Image 6-12 83
- 6.8.2 Source switching 84
- Switching mode set up 84
- 6.8.3 No signal 85
- No signal settings set up 85
- 6.8.4 Image load mode 86
- Howtosetuptheloadmode 86
- 6.8.5 Minimum frame delay 87
- How to toggle the delay 87
- 6.8.6 Contrast enhancement 88
- How to calibrate 89
- Howtosetthelenssettings 90
- 6.8.9 Auto picture alignment 91
- 6.8.10 LCD timeout settings 92
- 6.9 Maintenance 93
- 6.9.2 Reset electronics 94
- How to reset 94
- Image 6-24 95
- Reset formatter - PMP 95
- 7. CONFIGURATOR, PROJECTOR 97
- ALIGNMENT SETTINGS 97
- Image 7-2 98
- Lens mid position 98
- Image 7-3 98
- Lens zoom 98
- 7.2 Alignment pattern 99
- 7.3 Gamma adjustment 100
- Adjusting via the input field 101
- What can be done? 101
- Color selection 101
- What can be done ? 101
- 7.6 Blanking adjustment 102
- How to adjust a side blanking 103
- 7.7 ScenergiX 104
- 7.7.2 Preparations 105
- ScenergiX Preparations 105
- 7.7.3 ScenergiX activation 105
- Definitions 106
- How to set a blending zone 109
- Why black level adjustment 110
- Image 7-20 111
- DLP Leakage area set up 111
- Image 7-21 112
- Leakage area adjustment 112
- Image 7-22 112
- DLP leakage area 112
- How to adjust the black level 113
- Image 7-24 114
- 8. CONFIGURATOR, PROJECTOR 115
- ADJUSTMENT SETTINGS 115
- How to set native resolution 116
- Window selection 116
- Slot - input selection 117
- 8.3 Configuring an input slot 118
- Possible results 119
- Image 8-7 120
- Window status via properties 120
- 8.5 Input files 121
- 8.5.1 Introduction 122
- About files 122
- Types of source files 122
- Load via Load icon 122
- Load via the input window 123
- What is possible? 123
- How to load 123
- 8.5.4 Edit Input settings 124
- Adjustable items 124
- How to edit 124
- For direct save 126
- How to rename, way 1 126
- How to rename, way 2 127
- 8.5.7 Deleting an input file 128
- How to delete, way 1 128
- How to delete, way 2 129
- How to select 131
- If custom is selected 132
- 8.5.9 Input balance 133
- Analog Digital Conversion 134
- How can it be done ? 134
- Black balance 135
- Image 8-27 136
- Input balance adjustment 136
- Apredefined color temperature 137
- Image 8-28 138
- Color temperature 138
- A Custom color temperature 139
- 8.6 Image settings 140
- Adjusting via dragging 141
- 8.7 Layout settings 142
- 8.7.3 Show window border 143
- How to show 143
- 8.7.4 Re-size a layout window 143
- Re-size via drag and drop 144
- Re-size via width and height 144
- 8.7.5 Move a layout window 144
- Move via drag and drop 144
- Move via the coordinates 145
- How to change 145
- When custom is selected 146
- 8.7.7 Lock a input window 146
- How to lock 146
- Via the context menu 147
- Via the layout settings 147
- 8.7.9 Save a layout 148
- How to save 148
- 8.7.10 Layout Save as 148
- How to ’save as’ 148
- 8.7.11 Rename a layout 149
- How to rename 149
- 8.7.12 Delete a layout 150
- How to delete 150
- 8.7.13 Edit window texture 151
- Overview 151
- 8.7.13.1 Start up 151
- Introduction 151
- How to startup 151
- 8.7.13.2 Color fill 152
- Color fill or not 152
- Select a color 153
- Image 8-49 154
- Color value via swatches 154
- Image 8-50 154
- Color value via HSB 154
- 8.7.13.3 Picture 155
- Insert a picture 155
- Supported types 156
- Removal of a picture 156
- 9.2 Color space 157
- 9.3 Custom color space set up 158
- Setup via the color gamut 159
- 9.4 White point adjustment 160
- Setup via the coordinates 161
- How to adjust via the menu 162
- How to adjust via color gamut 163
- 9.5 Save custom settings 164
- Image 9-9 165
- Diagram preview set up 165
- SETTINGS 167
- Lamp power mode 168
- CLO mode (status) 169
- Lamp run time 169
- Lamp strikes 169
- How to set up 172
- IP address examples 173
- 11.2 Serial network address 174
- 11.3 DMX settings 174
- How to set a DMX address 175
- 11.3.2 DMX mode 175
- What are the possibilities ? 175
- 11.4 Infrared receivers 176
- Image 11-7 177
- Infrared receivers on - off 177
- 12. CONFIGURATOR, WARPING 179
- 12.3 Warp with commands 180
- 12. Configurator, Warping 181
- 12.4 Warp via User interface 184
- 13. CONFIGURATOR, WARP USER 191
- INTERFACE 191
- 13.1 About the Warp UI 192
- 13.2 About the Floater menu 193
- How to increase 194
- How to decrease 194
- 13.4 Make node selection 195
- Image 13-7 196
- Multi node selection 196
- Multi deselect 197
- Viathemouseclickinthegrid 198
- Via the Floater menu 198
- Via the keyboard 198
- How to make the adjustment 199
- About the arrow keys 199
- 13.8 Add a hard edge 200
- 13.9 Moveahardedgeline 201
- 13.10 Remove a hard edge 202
- How to save to file 203
- What is possible ? 204
- Howtoloadafile 204
- How to start up 205
- 13.15 Indentation 206
- 13.16 Gradient 207
- 13.17 Fast preview 208
- 13.19 Recover warping board 210
- 13.20 Preferences 210
- How to make the selection 211
- 13.20.4 Hard edges 212
- How to select the color 213
- 13.20.5 Color selection 213
- Image 13-36 214
- Image 13-37 214
- Image 13-38 215
- Color value via RGB 215
- 14. UPDATE MODULE 217
- 14. Update module 218
- 15. DIAGNOSTICS MODULE 221
- 15. Diagnostics module 222
- 15.3 History mode 223
- 16. LENS CALCULATOR 227
- 16. Lens calculator 228
- 16.4 Calculate a lens 229
- 16.5 Calculate distance 230
- 16.6 Calculate screen 230
- 17. SERVICE MODULE 233
- 17.3 Services FLM group 234
- 17. Service module 235
- GLOSSARY 237
- Glossary 238
- Revision Sheet 245
Relacionado con productos y manuales para Software Barco Projector Toolset
Software Barco NioWatch Manual de usuario
(147 paginas)
(147 paginas)
Software Barco Coronis 5MP Mammo Manual de usuario
(14 paginas)
(14 paginas)
Software Barco DC Toolset Manual de usuario
(79 paginas)
(79 paginas)
Software Barco Coronis 5MP Mammo Manual de usuario
(152 paginas)
(152 paginas)
Software Barco NioWatch Manual de usuario
(19 paginas)
(19 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales