Barco MDRC-2124 Manual de usuario

MDRC-2124 User manual

10 Recommendations for using your display system 1. Optimize the lifetime of your display Enabling the Display Power Management System (DPMS) of y

11 performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels. To learn more about

12 Cosmetics and oils on the skin are both detrimental to the screen and difficult to remove. • Allow the display to warm up to room temperature

13 Cleaning the display Observe the following guidelines to maintain display and LCD screen. • Use a clean, lint-free, absorbent cotton cloth to

14 Explanation of symbols DISPOSAL. Do not use household or municipal waste collection services for disposal of electrical and electronic equipmen

15 Introduction About the product Thank you for choosing Barco. The MDRC-2124 is an LCD display with an active matrix, thin-film transistor (TF

16 Package overview User manual USA Power Cord EUR Power Cord China Power Cord DisplayPort Signal Cable DVI-D Signal Cable Power A

17 Display parts, controls and connections Front View Power LED 1. Green indicates the display is turned on. 2. Orange indicates the display

18 Back View Control wheel 1. Press the control wheel for 1 sec to power off to the LCD Display. 2. Swivel the control wheel for OSD menu. Dis

19 Installation Connecting the display Use only the power adapter, power cord, and the video cables shipped with this display. To setup this di

2

20 Note: To ensure the LCD Display will work well with your computer, please configure the display mode of your graphics card to make it less th

21 Adjusting the display position Vertical height Portrait/Landscape Left to right pan Front to back tilt Remove display from stand

22 On-Screen Display menus How to use the OSD menus 1. When the display is on and the OSD in not on the screen, press the control wheel. The fron

23 6. To change an adjustment value or setting, swivel the control wheel to select the adjustment or setting. Next, press the control wheel to g

24 Adjustments menu Name Description Luminance Allows to manually adjust the luminance target if you’d experience the overall image is too dark o

25 Name Description Gamma 1.8 Gamma 2.2 Select one of these gamma options in case the display replaces a CRT display with a gamma of 1.8 or 2.2 r

26 User submenu Name Description Red Allows to manually adjust the image red level target. Green Allows to manually adjust the image green level

27 Name Description Horizontal Position Allows to manually adjust the horizontal position of the DVI analog image. Vertical Position Allows to ma

28 Name Description LED Allows to switch the power LED’s on state on/off. The LED’s orange DPMS state is not influenced by this setting. So, when

29 Information menu Name Description Display Name Indicates the display type. FW Version Indicates the current internal firmware version. Seria

3 Copyright notice This document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied

30 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following troubleshooting. If the problem persists,

31 Problem: Image is scrolling • Check and make sure the video signal cable (or adapter) is well connected. • Check and reconfigure the display

32 Product dimensions

33 Technical specifications LCD Panel Technology TFT Color LCD (E-IPS) Native resolution 1920x1200 Active screen diagonal 24.1" (611

34 OSD languages English, French, German, Spanish, Italian, Dutch, Simplified Chinese, Traditional Chinese, Korean, Japanese. Options Protectiv

35 Compatibility modes Standard Resolution Vertical Refresh (Hz) Horizontal Scan (kHz)IBM VGA 640x480 60 31.5 VESA VGA 800x600 60 37.9 VESA XGA

36 Regulatory Compliance Canada, European Union, United States This display has been tested and found to comply with IEC/UL/EN 60601-1 and IEC 606

37 The display was classified as required by the MDD according to Annex IX of the directive and the medical device (MEDDEV) guidance available at

38 EU EMC Directive 89/336/EEC EU Electromagnetic Compatibility Directive EN 60601-1-2 (2001) Collateral standard electromagnetic Medical Electri

39 IEC 61000-4-6 Conducted immunity IEC 61000-4-8 Magnetic field immunity Conformance to the Medical Device Directive 93/42/EEC EN 60601-1 Me

4 Table of Contents Table of Contents ... 4 Preface...

40 • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experi

41 BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1: PRODUCT WARRANTY Barco nv, Medical Imaging Division

42 1.3 The Customer shall return, freight prepaid, the defective equipment or subassemblies in its original packaging with the assigned RMA number

43 mal functioning of the hardware covered under this Agreement. 2.4 Normal wear and tear, use under circumstances exceeding specifications, such

44 iv. difference in color temperature as a result of not using all displays of a multi-head configuration at the same rate. v. LCD lum

45 version of the software. (c) The repair or replacement under the Warranties covers the cost of material and labor. ARTICLE 5: DISCLAIMER OF

46

47

B410640-02 November 2010 Barco nv Medical Imaging President Kennedypark 35 B-8500 Kortrijk, Belgium www.barco.com

5 Preface Important notice Notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibilit

6 Environmental information Disposal Information The lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of i

7 Safety Instructions General Recommendations • Read the safety and operating instructions before operating the display. • Retain safety and o

8 Intended use This display is an AMLCD display designed for viewing medical X-ray images. This unit should not be used near patients and should b

9 Equipment not complying with IEC 60601 must be kept outside the patient environment, as defined in the standard as at least 1.5 meters from the